Home > Products > Mustang > Overview

Mustang® Seamless Aluminium Gutter System

The Mustang® range of coils and components are an essential part of the BBA Approved gutter system. Coils are supplied dual coated and come in a range of fashionable colours with the corresponding components to match.

Benefits of the Mustang® Gutter System

  • No Joints, no leaksBBA Logo Certificate No 91/2625 ARP
  • Quick, easy and safe to install, most of the work is done on the ground.
  • Minimal maintenance, fit and forget!
  • Strong and fit for purpose, with a life expectancy in excess of 30 years accredited by the BBA
  • Quality assured – the only seamless aluminium gutter system with BBA approval in the UK
  • No wastage – Made to the exact dimensions of the building
  • Sustainable Product – Manufactured using recycled aluminium
  • Installed by ARP trained and approved contractors
  • Range of colour options 

 

Colour Options

RAL 9005 – Matt Black
RAL 9016 – Satin White

RAL 9005 – Matt Black
BS 08B29 – Matt Brown

RAL 7016 – Matt Anthracite
RAL 7037 – Matt Grey

Coil

Coil Colours Coil ThicknessWidthApprox LengthWeight
9005 Matt Black / 9016 Satin White0.9mm300mm137m100kg
9005 Matt Black / BS 08B29 Matt Brown0.9mm300mm137m100kg
7016 Matt Anthracite / 7037 Matt Grey0.9mm300mm137m100kg

External 90° Two Part Polycarbonate Interlocking Corner

Colour Options Pack Qty A
9005 Matt Black / 9016 Satin White1035mm
9005 Matt Black / BS 08B29 Matt Brown1035mm
7016 Matt Anthracite / 7037 Matt Grey1035mm

External 135° Two Part Polycarbonate Interlocking Corner

Colour Options Pack Qty A
9005 Matt Black / 9016 Satin White1035mm
9005 Matt Black / BS 08B29 Matt Brown1035mm
7016 Matt Anthracite / 7037 Matt Grey1035mm

Internal 90° Two Part Polycarbonate Interlocking Corner

Colour Options Pack Qty A
9005 Matt Black / 9016 Satin White1035mm
9005 Matt Black / BS 08B29 Matt Brown1035mm
7016 Matt Anthracite / 7037 Matt Grey1035mm

Polycarbonate Endcap

Colour Options Pack Qty A
9005 Matt Black / 9016 Satin White1015mm
9005 Matt Black / BS 08B29 Matt Brown1015mm
7016 Matt Anthracite / 7037 Matt Grey1015mm

Polycarbonate Straight Connector

Colour Options Pack Qty A
9005 Matt Black / 9016 Satin White1060mm
9005 Matt Black / BS 08B29 Matt Brown1060mm
7016 Matt Anthracite / 7037 Matt Grey1060mm

Leaf Trap

TypeA Pack Qty
Hard60mm25
Hard70mm25
Soft60mm25

Type A Hanger

A Pack Qty
Hanger A37mm500

Type C Hanger

A Pack Qty
Hanger A47mm500

Composition and Manufacture

  • Gutter formed on site from Hydrocoat Textured 800 Aluminium 0.9mm thick 3105 grade H45 Coil
  • Components made from colour matched UV stable Polycarbonate 
  • Matt Finish (40% reflectivity)
  • BBA Certificate No 91/2625
  • Life expectancy of over 30 years

Installation

Downpipes are positioned and mark’s corresponding to their centres are made on the fascia board. An exact measurement is taken of the length of gutter required, noting the marked positions of the downpipes. An initial 1m length of the gutter section is roll-formed and the process stopped for an end cap to be fitted to the open end. The gutter is crimped centrally near the edge of the rear, front and base to create raised fixing nibs. The end cap is pressed home activating the internal slotted securing clips to fully engage over the fixing nib, ensuring a non-removable fitting. The completed fitting is sealed inside the gutter with at least three beads of sealant, minimum diameter 7mm.

Roll-forming to the exact gutter length is then completed. Aluminium fixing brackets are clipped into position at centres not exceeding 450mm as roll-forming is continued. The formed gutter is cut to length and a stopend fitted to the remaining open end.  Corners are formed by mitring the ends of the gutter lengths and connecting with a two-piece polycarbonate locking corner fitting, which is then sealed with a specific sealant and secured with stainless steel screws. Connector expansion joints are installed in the same manner. The corners and connectors do not require mechanical fixing and allow for thermal movement. At the downpipe positions in the gutter a hole is formed using a Q-Max cutter into which a low-density polyethylene outlet/leaf trap is fitted and sealed with mastic. The gutter is positioned and fixed with 4mm diameter, 30mm long stainless steel, self tapping screws. The fixings are located in pre-drilled holes in the fixing brackets and driven through the back of the gutter into the fascia. 

Full fitting instructions are supplied with every delivery.